The washing machine erases for a long time - the reasons

A washing machine performs a washing program for a certain time. There are modes designed for half an hour, there are an hour or two. Naturally, the hostess, setting a half-hour program, expects that she will get clean and wrung out linen exactly thirty minutes later, and not a second more. But expectations do not always come true, sometimes the unit becomes too slow, or even freezes and cannot finish the job. If the washing machine is washing for a long time, the reasons may be different. They will be discussed in our article.

to contents ↑

What happens to the unit?

A washing machine is a rather complex device consisting of many elements. To answer the question why a washing machine erases for a long time, you need to understand what factors affect its operation:

• a set of water;
• draining;
• continuous cycle "set-discharge";
• heater operation.

In turn, failures in the operation of each of the systems depend on a variety of circumstances.

to contents ↑

The washing machine draws water for a long time

When water draws too slowly, the entire laundry cycle slows down too. Why is water not in a hurry to fill the tank? The reasons can be both in the machine itself and in the condition of the water supply. Therefore:

• First of all, check if the water pressure in the water supply is sufficient. To do this, just open the tap.
• For an automatic car, you need pressure in one atmosphere, in city apartments it usually is. But there are situations when utilities conduct work on city and intra-house networks, and then the pressure decreases. In this case, you do not need to repair anything in the car - it is best to postpone the washing.
• If the pressure is normal, but the water still pours slowly - check the bulk filter. This is the mesh that stands in the filler valve. It is removed easily - just unscrew the hose. Rinse the filters with running water.
• The reason may be hidden in the valve itself. Here you can’t get away with simple cleaning - you will have to change the element, putting it in exactly the same way as it was if possible.

to contents ↑

Drain problems

The unit can start to work slower than usual, and for the exact opposite reason - if the water leaves barely or does not want to leave the car at all. In this case, you will have to examine all the devices through which the spent liquid should go:

• drain hose;
• cleaning filters;
• branch pipe;
• sewer

Drain hose

The drain hose is an extremely simple device. But for normal operation, he must, first of all, occupy his characteristic position:

• There should not be any kinks, bends, and especially loops and squeezing.
• Take care that nothing stands on it - this is rarely the case with washers, but it does happen.
• Check if a button, coin, or anything else is stuck in the hose. Before you put clothes in the drum of the washer, you, of course, turned out the pockets, but you never know - the button could come off during washing, thereby slowing down the whole process.
• Make sure that the drain hose is installed at the correct height - 50-60 cm from the floor. In this case, the angle of inclination is optimal, which allows the water to leave quickly.

Important! Hose walls may overgrow.If the hole has become too small, it is better to simply replace the element with a similar one, since recognized manufacturers have no problems with this.

We clean a branch pipe

But cleaning the hose is the least evil. A blockage may also occur in the nozzle, as a result of which the washing machine will wash for a long time. Of course, there is not much trouble with it, but some tools like a screwdriver and pliers will be needed.

And you need to act like this:

1. Unplug the machine.
2. Lay the unit on its side so that the drain pump is on top.
3. Loosen the clamp (it connects the pipe to the pump).
4. Remove the nozzle.
5. Rinse it properly.
6. Put the pipe back.
7. Tighten the clamp.

Clogged drain filter

The cleaning filter, like the bulk filter, must be cleaned. It is much more susceptible to pollution, because small objects and particles of pile, wool, thread, etc. fall into it.

Important! Strainers last quite a long time, but they also have to be changed periodically. If such a need arose, try to find a filter specifically for the model that you have.

Sewage blockage

Water can slowly leave, respectively - the washing machine can be washed for a long time and because the sewer is clogged. This problem occurs if the drain of the machine is directly connected to the sewer pipe. Standard tools can help:

• plunger;
• “Mole” or other remedy;
• plumbing cable.

Important! To avoid such troubles, monitor the condition of the sewage system and eliminate even small blockages in time. Pipes must be flushed periodically.

to contents ↑

Water pours in and out

There are several reasons for this phenomenon:

• low hose installation;
• incorrect connection of the sewer;
• broken pressure switch.

If the drain hose is too low, water fills the drum and then leaves immediately. Accordingly, it does not heat up, the program does not start, and the washing process itself can take forever, that is, until the hostess gets tired and she starts to wash by hand. The way out is extremely simple - rearrange the hose.

Incorrect sewage connection

One of the most common reasons why a washing machine is washing for a long time. The problem usually manifests itself immediately after the first wash. It’s better to figure it out right away, otherwise you’ll wash four hours instead of two.

Incorrect connection results in spontaneous discharge. Accordingly - the unit can not get the water to the desired level.

Important! The pressure switch sends a signal to the control module that there is not enough water. As a result, the program does not work correctly. It either does not start, or the cycle continues indefinitely. Water continues to pour - and immediately follows.

There is a way out of the situation. Connect the unit to the sewage system using a special drain siphon.

The pressure switch is broken

The pressure switch is an indicator of the water level. Its data goes to the control module. Accordingly, if this sensor breaks down, the wrong signal arrives at the module, which causes certain consequences.

Water will continue to pour and pour out at the same time. Surplus will go to the sewer, and washing may not start.

Important! Repairing the pressure switch does not make sense, you just need to change it.

Inlet valve

Malfunctions in the intake valve are relatively rare, but you may encounter this situation. A broken valve does not close, respectively - water continues to flow in and out, and so on ad infinitum.

to contents ↑

Vagaries of the heater

The washing cycle can increase dramatically if the heater has stopped working as it should. This increases the energy consumption. You set the desired mode, the water should heat up, but it can not reach the desired temperature.

As a result, the unit is in no hurry to start work, it waits until the temperature rises to the desired level. And it can wait a very long time. This means one of two things:

• problems with the heater;
• failure of the temperature sensor.

Important! Does this mean that the heater is out of order? Not always. It may form a layer of salts - scale. This happens especially often in places where the water is very hard, and car owners do not like to use softeners.

What to do with TEN?

First you need to determine what exactly happens to him:

• The machine suddenly began to wash slowly.
• Washing time increased gradually.

In the first case, the heater, obviously, has already lived its century and needs to be replaced. To begin with, call it a tester, then it will immediately become clear whether it burned out or not. You can replace it in the service center, but you can do it yourself if you wish - the element is removed quite easily, and instructions for what to do in such cases are attached to each machine from a decent manufacturer.

Important! By the way, in modern models there is a self-diagnosis function. Each problem has a specific code that appears on the display. So you can find out that the heating element has failed, without any tester.

Will the machine work at all if the heater is out of order? It depends on the model. For some, the washing stops and the car freezes. Others calmly continue to wash, but in cold water, accordingly, quality suffers.

Scale on the heater

It happens that the washing time increases gradually, the hostess does not notice this for a long time and does not take any measures. But one fine day the thought dawns on her that the car is fiddling with laundry for too long.

A gradual increase in washing time means that the heater itself is in order, but it would be nice to clean it. To do this, it is not necessary to disassemble the car. It is enough to wash without laundry, but with the addition of citric acid.

The temperature sensor is important

The temperature sensor determines the temperature of the water and sends a signal to the control module that it is necessary to start washing. If this element fails, the module receives the wrong signal and reacts accordingly - or does not respond at all. The only way out is to replace the thermostat.

to contents ↑

Failure in the electronic module

If the heater is in order, the drain and water systems work fine, and the machine still erases for a long time - check the module. This is very clearly visible. The drum cannot stop, or vice versa - suddenly freezes.

Like any smart technique, the washer depends on the “electronic brain”. You are unlikely to be able to cope with this scourge on your own. Call the wizard. It is possible that you will need to reflash the module.

Important! The reason for the failure of the module may be an unexpected power outage. Do not park the car where there is no stable power supply.

to contents ↑

Drum overload

Eliminating this reason why the washing machine takes a long time to wash is entirely up to you. If you put more laundry in the drum than it should be according to the instructions, it will spin for a long time, thereby slowing down the process.

But in some models, a slowdown in washing can occur with an imbalance. This is typical for older models that cannot independently control the balance. Help the machine - distribute the laundry evenly throughout the drum.

Important! If the drum stopped unexpectedly - interrupt the wash, drain the water and remove excess laundry.

to contents ↑

Stock footage

Now you know about all the reasons why the washing machine erases for a long time. Identify the one that takes place precisely in your case, so that your “assistant” will continue to properly perform their duties.